Sign up! UsernameUsername  PasswordPassword  Do login

Note: "The components depicted in this picture are for information purposes and in some instances they may not be the actual component of the product being purchased"

Wind Sensor

1. Technical data

  • Power: NI-MH/3.6V Solar panel + battery
  • Protection index: IP44
  • Temperature: -20ºC to +60ºC
  • Working current: <=12mA
  • Codes: Rolling codes
  • Frequency: 433.92 MHz

 

2. Structure

windsensor

3. Size

windsensor2

4. Installation

Note: To make the system operate normally, please remember that the controller must be installed near the place where the awning can be protected, and the place can reflects the surrounding´s light intensity and wind speed. Please ensure that there is no other same frequency (433.92 MHz) device to work constantly; otherwise, the system will be interfered.

1.    Please use the material offered by our company to install and fix the product in the suitable place.
2.    Please make the product´s mechanical position fit to the wind cup parallel the level surface, just as the installation drawing.

01. Installation

windsensor3

02. Installation chart

windsensor3b


5. Code learning

01. Confirm that the only motor being programmed is powered.
02. Press learning button on the master transmitter until the motor moves then release the button.
03. Press the learning button on the wind-light sensor until the motor vibrates.
Note: The wind.light sensor can not be set as master transmitter.

6. Set Wind Grade

windsensor4

1)Long press the left button for 2 seconds and the left numbers on the LCD would flash. 2)Short press the left button and the numbers will circulate from 0 to 5. 3)Select the figure you want and then press the right button one time to exit the setting. The numbers stop fashing and the wind grade is set.

Chart 1.1 wind grade corresponding to actual wind speed

Wind Grade Wind Speed
0 Close wind speed test
1 10km/h
2 15km/h
3 20km/h
4 30km/h
5 40km/h

 

7. Set light intensity

windsensor5

1)Long press the right button for 2 seconds and the right numbers on de LCD would flash 2)Short press the right button and the numbers will circulate from 0 to 5. 3)Select the figure you want and then press the left buttom one time to exit the setting. The numbers stop flashing and the light intensity is set.

Chart 1.1 wind grade corresponding to actual wind speed

Light grade Actual Light intensity Light Grade Actual Light intensity
0 Close light intensity test
5 40000 Lux
1 2000 Lux 6 60000 Lux
2 5000 Lux 7 70000 Lux
3 10000 Lux 8 80000 Lux
4 20000 Lux 9 90000 Lux

 

8. Testing mode

1. Wind speed testing mode
When the sensor is in wind speed real-time testing mode, the figures reflect current wind speed outside. For example, the figure “1.0” represents real wind speed is 10 km/h outside.

windsensor6

1)Short press the left button four times. 2)The dot in the middle is always on. 3)Short press the right button once, it will come out from wind speed testing mode.

2. Light intensity testing mode
When the sensor is in light real-time testing mode, the figures reflect current light intensity outside. For example the figure “10” represents real light intensity is 10000 Lux outside.

windsensor7

1)Short press the right button four times. 2)The dot at the right corner of the LCD is always on. 3)Short press the left button once, it will come out from light intensity testing mode.


Note: In light intensity testing mode, the numerical value displays the light intensity from 1000 to 100000lx. It shows “00” below 1000lx, and “99” above 100000lx. For example, the figure “12” represents 12000lx. It will return to initial interface 3 minutes later if there is no further operation is done to the sensor.

 

9. Function

1. The strong wind protection function

windsensor8

If the wind speed exceeds the set grade for 6 seconds continuosly, an Up order is given to the motor and the awning will close automatically. As long as real wind speed is higher than the set grade, you can´t open the awning by any means (manual control, emitter control and light sensor are invalid). If the wind speed falls below the set grade for 30 seconds continuously, the sensor sends signals to the motor and activates the control by emitter and light sensor.

 

2. The light sensor function

windsensor9

If the light intensity exceeds the set grade for 10 minutes continuosly, a Down order is given to the motor an the awning opens automatically. If the light intensity below the set grade for 10 minutes continuously an Up order is given to the awning and the awning closes automatically.
windsensor10
 

The sensor is wireless emitter which controls awning to open or close according to the change of light intensity. Also it detects real-time wind speed and control awning to close automatically if the wind exceeds set limit. It is powered by solar panel and can work continuosly more than two weeks in rainy or cloudy days. It is environmental-friendly.